How To Build A Bookcase

So I used a 18 for each shelf and 12 across the front to give the shelf more thickness and make them flush with the side face 1x4s. Guide so I made one by cutting a 12-in.

How To Build A Bookcase Step By Step Woodworking Plans Bookshelves Diy Built In Bookcase Diy Furniture

A set of sawhorses under a sheet of 34-in.

How to build a bookcase. Drill holes into the sides and start screwing the shelves in. A bookcase is basically a five-sided box with the front part open so to begin constructing one first cut the pieces for the first four sides. Then use a table saw to cut the boards with the good side facing up so they look better.

Design your shelving based on your available space. Dont add pocket holes to the top board. Make its depth 1 12 to 2 in.

Repeat until every shelf but the top board has four pocket holes. Paint the bookcase if youd like or create the handsome antique finish we did. Less than the depth of the bookcase itself.

Sand apply first coat primer if you want fill nail holes and sand again apply final coat. Using the outer edge of the jig as a space drill using the innermost hole of the jig. Blend these in a separate container and apply them to the sanded surface with a clean rag.

Super easy but quite boring. I built the doors for this bookcase but showing you how to do that is a whole tutorial in itself. Use the jig and clamp to drill a 34-inch deep pocket hole near each corner for all five shelves.

Next Im ripping the wood down in 8 inches width which will. Begin construction by using a tape measure to mark the length of a side panel on 1 x 10 stock and lay out the cut line with a square. We used gel stain and mixed five parts cherry to two parts red mahogany to one part special walnut.

Strip off one side of my birch plywood. The side panels on our bookcase are 48 in. All it involves is re-utilizing old crates that have probably been condemned by the storeowner or if youre looking at new ones a variety is available online from where they can be procured at a good price.

Stain or prime it and allow it to dry. All included in this free bookcase plan are step-by-step instructions a list of tools and materials youll need as well as figures and pictures. Use a sharp 40-tooth carbide blade for finer cuts.

Put the top and bottom on Glue the top board on the bookcase and screw securely. Its height must be 18 in. Measure the height of the space where the bookcase will go.

Before you cut and assemble any parts sand all the wood. Craftsman-Style Bookcase Plan from Family Handyman. With the first piece of 34 ply laid out mark out the first.

Once all of the boards are cut use wood glue and 2 screws to attach the sides to the base. You will want to break up your shelving with vertical sections every 30 or less- anything more and your shelving will sag. Sand the bookcase with 100-grit sandpaper followed by 150-grit.

Plywood will work just fine. When you build a bookshelf try to make the shelves 12 or 16 inches deep so they fit most books better. Heres the completed bookcase all filled up and sitting in place.

Taller than the baseboard molding you plan to. Measure the distance between the edge of the base and the blade and adjust the plywood guide accordingly. Wide youll later use to construct each of the four standards.

Choose the height needed and stack three to four of these to make a bookcase. Add or remove blocks to create a perfect fit for any space. If youre making built-in bookcases measure the space available both at the bottom and the top- dont assume your walls are plumb and square.

I didnt have an extra sheet of plywood to use as an 8-ft. To make the cut I simply have another piece of wood underneath and the depth of the blade set quite shallow to about 34 of an inch. Start by building a base out of 1x or 2x lumber.

For plans to build this exact bookcase click here. Family Handyman has a free bookcase plan that builds a classic Craftsman-style bookcase. You want to use a drill with a countersink so that you can drill holes that can be plugged later on.

Consider painting a few of the. Have the lumberyard rip your plywood into boards to the width that matches your bookcase depth. The first order of business is to rip cut lengthwise the eight pieces of plywood 13-34 in.

I added three shelves to each side and spaced them out evenly in the vertical space. You dont need a fancy shop to cut the plywood and build the standards for this how to build a bookshelf project. Simple cuts of wood and rope work in concert to form a flexible DIY bookcase.

Im not going to cover every step of the finishing process as its incredibly boring and simple.

How To Build A Classic Floor To Ceiling Bookcase Diy